California Fencing Contractor (C-13) License Practice Exam

These questions are part of the practice quiz. Start practicing

• Which two CSLB exams are typically required to obtain the C-13 Fencing Contractor license?
• To which side effects of the posts should wire mesh fabric be attached, according to CalTrans?
• Why is end-post and terminal-post installation critical for gate operation?
• Wood jambs for gates may be fastened to masonry walls with:
• The corners of the gate frames should be fastened together and reinforced with which option?
• Which orientation is correct for installing a tap?
• Which of the following is recommended for maximum post security?
• All iron surfaces should be ___ after assembly and installing them into wood posts or rails.
• A traditional method used to fasten wrought metal parts together is which of the following?
• Which statement best describes the consequences of missing statutory deadlines in mechanics liens?
• What is a typical approach to aligning multiple gates along a fence line?
• Which sign indicates potential UV damage in vinyl fencing?
• Which factors influence material waste allowances in a fencing project?
• Before assembling them, which action should be taken on metal where two pieces touch?
• Which bolt is best for a brace band?
• How do you verify fence height compliance with code?
• What is the purpose of setting posts in concrete and adding bracing?
• Which practice best helps ensure posts remain upright and gate frames square during installation?
• Which statement is most accurate about plan measurements in relation to the actual site?
• When repairing damaged coatings, all welds made after galvanizing shall be ground smooth and wire brushed; the cleaned areas shall be coated with which material?
• Entry gates usually swing which direction?
• What is the primary function of a gate post in a fence system?
• How does chain-link fabric mesh size affect privacy and security?
• Posts anchored in concrete may be removed by:
• How does the Mechanics Lien law relate to fencing contractors in California?
• When an automatic backup warning device is used, it must be normally audible from a distance of how many feet?
• According to CalTrans, posts from each lot must be tested up to which number?
• Under which condition is aluminum considered the best option for ornamental fencing?
• What are common scale options for plan drawings used in residential fencing projects?
• Why is proper tensioning of chain-link fabric critical?
• Which of the following is a correct sequence of safety and prep steps before pouring fence footing concrete?
• According to CalTrans, all earth, trees, brushes, and other obstructions that interfere with the proper construction of fences:
• According to CalTrans specs, how are fence quantities paid for (with the exception of gates) ?
• The best material for securing a steel post in a concrete hole is which of the following?
• Hinges may be secured to metal gates in which of the following ways?
• Which actions are taken before assembling metal pieces that touch?
• Extending footings below the frost depth per local codes accomplishes what?
• Which factor is not typically considered when sizing post-hole diameter?
• Which distance conversion is correct for one mile in feet?
• If the bolt must pass through the post when fastening a hinge to a wood post, which hinge should be used?
• Which length and tolerance is specified for roll chain link fence material under ASTM standards?
• How should vinyl fence posts be anchored, and what is the role of footings?
• Which document would you review to determine required gate hardware for a fence project?
• You are fastening a hinge to a wooden gate post. If the bolt must go through the post, what type of hinge would you use?
• Which material is described as offering superior corrosion resistance and low maintenance?
• What essential safety steps are required when digging footings?
• Typical fence line posts should be set in undisturbed earth by _______.
• What is the consequence of poor compatibility between concrete mix, soil, and posts?
• Why is corrosion-resistant fasteners important in metal fences?
• When estimating labor, which tasks should be included?
• How are fence line and gate locations determined from a site plan?
• On sloped ground, hang gates to swing toward which side if possible?
• What is the purpose of corrosion-resistant coatings on chain-link hardware?
• For tubed fence, such as welded, bent rail type, which tubing pairing is easier to work with?
• Where do you put a turnbuckle on a wood gate frame?
• Which installation step reduces the likelihood of post movement?
• What is the purpose of a 'takeoff' in estimating fencing work from plans?
• What arithmetic operation determines how many top rail pieces are required from total length and piece length?
• Why is drainage and ventilation around posts important for wooden fences?
• What is the purpose of using forms around fence post footings?
• ____ ornamental fence is most widely used material but requires the most maintenance.
• What are the nails to which cover material directly attached known as?
• On sloped ground, which side should gates swing toward if possible?
• When ornamental iron is installed onto or through wood, what should be avoided?
• Which type of insurance and bonding are generally required for a California fencing contractor to operate legally?
• What are typical advantages of vinyl fencing compared to wood?
• Which device is used to bend sheet steel into the desired shape?
• How should drainage and grading influence fence installation?
• Which finish is specified for all gate hardware to prevent corrosion?
• When laying out multiple gates, which practice supports consistent operation?
• Which state agency administers contractor licensing in California, including the C-13 class?
• Which tools are recommended to maintain consistent gate alignment along a fence line?
• Present day wrought metal items are usually made of hot rolled, low carbon steel or duct alloys of which two materials?
• Wood jambs for gates may be fastened to masonry walls with which combination of fasteners?
• Gate latches can be made from which materials?
• What finish is recommended for iron surfaces after installation to protect from rust?
• Clearing the fence line consists of which of the following?
• Which method is not listed for securing hinges to metal gates?
• Which of the following is not used with wood gates?
• Which method is best for connecting fabric to wrought iron fences?
• Which agency's specifications are cited for testing and fence-related requirements in these examples?
• According to CalTrans, braces from each lot must be tested up to which number?
• Installing chain link kennel panels to existing buildings may be done by attaching the panels using:
• Double-drive gates are most often used on which type of ground?
• Besides squares, what type of nut is used w machine screws?
• The easiest joint to use is the which joint?
• Which post type is typically driven into the ground?
• What steps ensure proper gate alignment with metal fences?
• Which of the following can be used to set steel posts?
• Panel boards on a wood retaining wall should be installed on the back of the posts.
• You are fastening a hinge to a wooden post. If the bolt must go through the post, what type of hinge would you use?
• If corrosion is more of a maintenance concern than strength and rigidity, ___ ornamental fencing may be your best alternative
• What is the length for a roll chain link fence material, according to ASTM standards?
• What is the purpose of line stakes in laying out a fence?
• ___ ornamental fence systems offer superior corrosion resistance and low maintenance.
• If ponding occurs near gate posts, what issue is most likely to result?
• Which method is recommended to connect fabric to wrought metal parts in fencing?
• End-post and terminal-post installation influences what?
• According to ASTM specifications, all exposed ends of tubular posts should be fitted with caps of:
• Gate openings on chain link fences are measured inside to inside. Which of the following is NOT a correct alternative measurement listed in typical practice?
• Which statement about the CSLB is true?
• There should be no __ where ornamental iron is installed onto or through wood.
• Why is it important to review specifications for fence style, height, and gate hardware in plans?
• What is the best way to remove an existing post?
• How are gate openings measured on chain link fences?
• Which coatings protect metal fences from corrosion in coastal environments?
• According to CalTrans specifications, posts from each lot of how many posts or less must be tested, and braces from each lot of how many braces?
• What tool is listed as the best option for removing a post with a concrete base when a mechanical post puller is unavailable?
• Why is drainage around footings important?
• What factors influence gate swing versus sliding gate installation?
• What maintenance is required for vinyl fences?
• Panel boards on a wood retaining wall should be installed on which side of the posts?
• Which of the following gate latches are padlockable?
• How should gate hinges and latches be installed for durability?
• Which of the following can be used to set steel posts?
• Which of the following posts may be driven?
• Which of the following aren't used with wood gates?
• What is the typical requirement for clearance under a fence for accessibility or drainage?
• What is the best bolt to use for a brace band?
• What unit of measure is used for paying fence quantities (excluding gates)?
• When repairing damaged coatings, after galvanizing, welds shall be ground smooth and wire brushed to remove loose or burned zinc coating, after which the cleaned areas shall be prepared and neatly coated with which substance?
• Which components are commonly included in a takeoff for a chain-link fence?
• Which hardware practice aligns with vinyl installation guidance?
• Sheet steel is cut with a ___ and bent into the desired shape with ___?
• How are quantities of chain link fabric measured?
• How should labor for fencing installation be priced?
• Which statement best describes rot-resistant wood use for fence posts?
• Which of the following is a correct statement about 'H' posts?
• If a job requires 400 linear feet of fabric and 400 feet of top rail, how many pieces are needed if top rail comes in 21-foot lengths?
• What are common concrete mix considerations for fence footings?
• What is a typical consideration for post-hole diameter relative to post size?
• How many miles is 38 km?
• What installation considerations are unique to vinyl fencing?
• According to CalTrans specifications, gate latches must be:
• Power driven staples aren't permitted on:
• All fittings, latches, rods, and other gate hardware shall be which of the following?
• Where a grooved post and horizontal drop in boards are used, it is best to use a(n):
• What are the nails called that attach cover material directly to a fence frame?
• Which nut shape is used with machine screws besides squares?
• How is post spacing calculated for a typical wood picket fence?
• If a single gate is located at the corner of a fence, it should swing:
• The major ingredients in concrete are:
• Standard 9-gauge fabric requires less tension than which gauge?
• During vinyl fence installation, which practice helps prevent warping or buckling?
• What is the role of end posts versus line posts in chain-link fencing?
• Which components are part of a basic chain-link fence system?
• How should posts be treated to resist rot at ground level?
• Which type of hinge may be used to flush-mount a gate with a narrow gate posts?
• What is the value of a written scope of work in a fencing bid?
• What shape nut (besides squares) is used with machine screws?
• What is the role of tension bands in chain-link fencing?
• What safety features are required for automatic gate operators?
• If a fence section pulls loose from its anchor rod in a block wall, what is the recommended repair?
• Properly stretched fabric won't ___.
• When a single gate is located at the corner of a fence, it should swing toward which position to be out of the way when open?
• Which items are cited as differences between hanging wood gates and iron/metal gates?
• What is the proper way to install a tap?
• Standard 9-gauge fabric requires less tension than:
• What is a major benefit of metal ornamental fences?
• A galvanized surface has been damaged. The contractor wire brushes the surface to remove the cracked coating, and then used spray paint to apply unthinned zinc rich paint to the cleaned areas. The contractor proceeded:
• Which statement about frost depth and footings is true?
• What is the primary purpose of the CSLB 'Law and Business' portion of the exam?
• What maintenance considerations should you address for wooden fences?
• To remove an existing post with a concrete base, which tool is best?
• Gate latches must be made of which materials?
• One mile is equal to how many feet?
• Which wood species are commonly used for exterior fencing due to durability?
• When reading project plans for a fence installation, what is typically shown in the site plan?
• In vinyl fencing, which factor most influences long-term stability in wet climates?
• In residential fencing plans, which scale option is not commonly used?
• Which if the following statements about caps on tubular posts is NOT correct?
• Which sources should you review to determine fence line location and avoid disputes?
• The type of bolt which has a coarse thread, a smooth round head and a black rough finish is the:
• Which tool is used to cut sheet steel?
• Which hinge should be used to fasten a hinge to a wood gate post when the bolt must pass through the post?
• Why is frost depth important when designing fence footings?
• What are common failure modes for vinyl fencing?